行业资讯当前位置:网站杭州临安吉码科技有限公司 > 新闻资讯 > 行业资讯

数控线材折弯机需要人工参与操作吗?

编辑:吉码科技 来源:www。jimaspring。com

 数控线材折弯机需要人工参与操作吗?答案是肯定的,但是,相比较而言,参与的操作的人数、工作量和劳动强度等都明显下降,一个人可以操作多台设备生产运行,人工只是注意查看设备生产正常与否和整理生产好的产品等协助性工作。

数控线材折弯机使用步骤:
  1、首先是接通电源,在控制面板上打开钥匙开关,再按油泵启动。
  2、行程调节,数控线材折弯机使用必须要注意调节行程,在折弯前一定要试车。折弯机上模下行至较底部时必须保证有一个板厚的间隙,否则会对模具和机器造成损坏。行程的调节也是有电动快速调整和手动微调。
  3、折弯槽口选择,一般要选择板厚的8倍宽度的槽口。如折弯4mm的板料,需选择32左右的槽口。
  4、数控线材折弯机的后挡料调整一般都有电动快速调整和手动微调。
  5、踩下脚踏开关开始折弯,折弯机与剪板机不同,可以随时松开,松开脚折弯机便停下,再踩继续下行。
  所以,数控线材折弯机需要人工参与操作吗?以上是关于本文的内容啦!杭州临安吉码科技有限公司专注于各种数控设备的研发、生产与销售,主要产品有弹簧机、座椅弹簧机、数控线材折弯机、自动弹簧机、数控线材折弯机等,广泛应用于各种线材产品的成型加工,欢迎咨询。
Does CNC wire bending machine need manual operation? The answer is yes, but by comparison, the number of people involved in the operation, workload and labor intensity are significantly reduced. One person can operate multiple equipment production and operation, and the human just pays attention to check whether the equipment production is normal or not and sort out good products and other assisting work.
 
Use steps of CNC wire bending machine:
 
1. First, switch on the power, open the key switch on the control panel, and then press the oil pump to start.
 
2, stroke adjustment, CNC wire bending machine must pay attention to the use of stroke adjustment, before bending must be tested. When the die on the bending machine goes down to the bottom, there must be a thickness gap, otherwise it will damage the die and the machine. The adjustment of the stroke is also electric fast adjustment and manual fine-tuning.
 
3, bending groove selection, generally choose the plate thickness of 8 times the width of the groove. If the bending of 4mm plate, need to choose about 32 notch.
 
4, CNC wire bending machine rear baffle adjustment are generally electric fast adjustment and manual fine tuning.
 
5, step on the foot switch to start bending, bending machine and shear machine, can be released at any time, release the foot bending machine will stop, then continue to step down.
 
So, does CNC wire bending machine need manual operation? Above is about the content of this article! Hangzhou Lin 'an jima technology co., ltd. focuses on the development, production and sales of various CNC equipment, the main products are spring machine, seat spring machine, CNC wire bending machine, automatic spring machine, CNC wire bending machine, etc., widely used in a variety of wire products molding processing, welcome to consult.

江苏恩华药业股份有限公司 徐州润田打沟机网 石家庄德淼科技有限公司 立智环保有限公司 常州市茂宏干燥设备有限公司 厦门众丽光电科技有限公司 淄博岳峰装岩机公司 河北格瑞玻璃棉有限公司 杭州临安吉码科技有限公司新昌县奔发机械有限公司 郑州亿升化工有限公司